>UPSCABLE usb все именно так прописано
хм все равно не пойму почему ругается...
вот полностью
## apcupsd.conf v1.1 ##
# for apcupsd release 3.14.2 (15 September 2007) - freebsd
# ========= General configuration parameters ============
UPSCABLE usb
UPSTYPE smartups
DEVICE /dev/ugen0
# LOCKFILE <path to lockfile>
LOCKFILE /var/spool/lock
# SCRIPTDIR <path to script directory>
SCRIPTDIR /usr/local/etc/apcupsd
# PWRFAILDIR <path to powerfail directory>
PWRFAILDIR /var/run
# NOLOGINDIR <path to nologin directory>
NOLOGINDIR /var/run
# ======== Configuration parameters used during power failures ==========
ONBATTERYDELAY 6
BATTERYLEVEL 5
MINUTES 10
TIMEOUT 0
ANNOY 300
ANNOYDELAY 60
NOLOGON disable
KILLDELAY 0
# ==== Configuration statements for Network Information Server ====
NETSERVER on
NISIP 192.168.2.2
NISPORT 3551
EVENTSFILE /var/log/apcupsd.events
EVENTSFILEMAX 10
# ========== Configuration statements used if sharing =============
# a UPS with more than one machine
UPSCLASS sharemaster
UPSMODE share
# ===== Configuration statements to control apcupsd system logging ========
STATTIME 0
STATFILE /var/log/apcupsd.status
LOGSTATS on
DATATIME 0
# ========== Configuration statements used in updating the UPS EPROM =========
# UPS delay after power return (seconds)
# WAKEUP 000 060 180 300 (default = 0)
#WAKEUP 60
# UPS Grace period after request to power off (seconds)
# SLEEP 020 180 300 600 (default = 20)
#SLEEP 180
# Low line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 106 103 100 097
# M 177 172 168 182
# A 092 090 088 086
# I 208 204 200 196 (default = 0 => not valid)
#LOTRANSFER 208
# High line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 127 130 133 136
# M 229 234 239 224
# A 108 110 112 114
# I 253 257 261 265 (default = 0 => not valid)
#HITRANSFER 253
# Battery charge needed to restore power
# RETURNCHARGE 00 15 50 90 (default = 15)
#RETURNCHARGE 15
# Alarm delay
# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never
# BEEPSTATE 0 T L N (default = 0)
#BEEPSTATE T
# Low battery warning delay in minutes
# LOWBATT 02 05 07 10 (default = 02)
#LOWBATT 2
# UPS Output voltage when running on batteries
# The permitted values depend on your model as defined by last letter
# of FIRMWARE or APCMODEL. Some representative values are:
# D 115
# M 208
# A 100
# I 230 240 220 225 (default = 0 => not valid)
#OUTPUTVOLTS 230
# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
# SELFTEST 336 168 ON OFF (default = 336)
#SELFTEST 336
и при старте все так же пишет ...
Wed Dec 24 16:30:38 MSK 2008 apcupsd FATAL ERROR in smartsetup.c at line 171
PANIC! Cannot communicate with UPS via serial port.
Please make sure the port specified on the DEVICE directive is correct,
and that your cable specification on the UPSCABLE directive is correct.
Wed Dec 24 16:30:38 MSK 2008 apcupsd error shutdown completed
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
(ok) on 19-Дек-08, 18:57 
